Model HCDX-10000 Magnetic Particle Inspection Equipment For Lab / Workshop

Model HCDX-10000 Magnetic Particle inspection Equipment

1. Equipment composition

Control center (including operation panel, control panel and main power board etc.)

Control system (SIEMENS)

Main engine (including clamping mechanism, magnetization mechanism, electrode mechanism, etc.)

Magnetic suspension spray system

Darkroom system

Coil movement device

Clamping and rotating mechanism

Bracket rotating mechanism

2. Inspection workpiece:

Shaft specification:

Workpiece rotation diameter of less than 400mm, within a length of 2000mm

3. Equipment capacity:

Running time: more than 500 hours / month

4. Local design standards:

JB/T8290 - 1998 "magnetic particle flaw detector"

5. Main technical indexes

Circumferential magnetization current AC:0 - 10000A FWDC, continuous adjustable, with power off phase control

Longitudinal magnetization magnetic potential AC:0 - 16000AT, continuous adjustable, with power off phase control.

Electrode spacing: 200 - 2500mm.

Magnetization method: direct pass method, coil method.

Magnetization mode: three kinds of circumferential magnetization, longitudinal magnetization and compound magnetization can be flexibly chosen.

The use of the environment: - 10 C and C +40, relative humidity is less than 90%.

Storage environment: temperature of - 20 C and 60 C, relative humidity is less than 70%. Non corrosive

Gas dust and high frequency electromagnetic pollution.

Sensitivity test: according to the People's Republic of China machinery industry standard JB/T6065 - 92, "magnetic powder testing standard test film", AII, test piece display clear. And standard DIN EN ISO 9934.

Power supply: three-phase four wire, 380V + 10%, 50HZ, about 600A.

Inspection surface: all surface cracks and other defects.

Demagnetization AC: automatic attenuation type demagnetization.

Demagnetization; DC:; ultra low frequency demagnetization

Remanence: the maximum remanent magnetization after demagnetization is less than 0.3mT

Workpiece rotation speed: 4-6rpm. (large workpiece bracket rotating, small workpiece clamping rotation)

Magnetization coil: inner diameter 400mm. The coil moves in an electric way.

Pneumatic clamping: clamping stroke 0-75mm.

Air pressure: 0.4 - 0.8MP.

Power control cabinet: 900 (width) * 1200 (long) * 2000 (high) mm.

Test bed (including UV lamp): 1000 (width) * 3500 (long) * 2100 (high) mm.

Temporary loading rate: less than 20%

6. Running program: manual and automatic

The automatic program is: clamping - liquid - magnetization - rotation observation (clamping and bracket rotation two) - demagnetization - loose clamp, the whole process is controlled by small industrial PLC (long workpiece, subsection magnetization)

7. Control center

The control center is based on programmable logic controller (PLC). Control cabinet as the main body, contains a variety of actuators, magnetization trigger circuit, the main transformer

8. Host

The host is composed of main body, stainless steel tank, longitudinal magnetization, coil to weeks of moving mechanism, carrier rotating mechanism, sprinkler system, rail, pneumatic mechanism and circumferential and longitudinal main transformer

Figure 2, each part of the equipment

Body: horizontal sheet metal structure, making use of the high quality material of the equipment.

Stainless steel collection tank: made of 1.5mm stainless steel.

Longitudinal magnetizer: consisting of coils.

The circumferential magnetizer consists of two electrically connected electrode plates and an electrode shaft.

Suspension system of magnetic suspension: the injection quantity can be adjusted by moving the valve. With stirring device antimagnetic precipitation powder. The circuit is provided with a filter convenient for replacing.

Rail: for supporting and moving coil and mobile electrode.

Electrode box: welded by 10mm steel plate.

Rotating mechanism: by the speed reduction motor through the chain transmission mechanism, the transmission roller to drive the workpiece Rotate or clamp workpiece rotation.

Coil movement mechanism: consisting of a gear rack mechanism.

The pneumatic mechanism consists of a cylinder, solenoid valve, control valve, air source treatment components, used for clamping, has Xiangtong electromagnetic, ensure the detection sensitivity.

9.Lighting

Equipped with white light and UV light system. The intensity of UV irradiation is up to standard

10.Others

An operating panel for mobile operation is installed on the host computer.

The device is installed on the ground without the equipment foundation.

Grease is butter.

Install the muffler on the solenoid valve.

Install air handling triple parts.

Use a limit switch with excellent heat and dust resistance.

The wires are wired at both ends

11.Features and functions

Compound magnetization solves the problem that once the workpiece is magnetized in all directions without missing.

The main circuit is contactless control, and the equipment is stable.

The flaw detector adopts PLC centralized control.

This machine adopts low voltage high current output current, ampere, adjustable.

The working principle of overview: This machine with programmable logic controller (PLC) as the core, according to the detection process, send information by the sensor, after PLC treatment, were judged to control mechanical action related, according to set parameters, week longitudinal magnetization, using special thyristor phase-shift trigger integrated circuit to control the circumferential and longitudinal silicon controlled trigger circuit. Output trigger pulse

Characteristic:

Through touch screen input, storage, detection process, rapid call detection process.

Part counter.

Over current and under current sound and light alarm.

Clamping function for both hands safety control.

Magnetizing current and phase difference of 120 Eve joy.

The electrode has a copper pad against sparking.

12.Business conditions

1. User owned

(1) power supply: supply a designated place (a place), 380V, 50HZ, > 250A.

(2) air source: supply a designated place (one) greater than 0.4Mpa.

2. delivery date

(1) 60 working days after ordering, to the design, manufacture and inspection of the factory.

13. Selection of magnetizing current

The circumferential magnetization current can generally be calculated in the lower order

Continuous method: I=8D to 15D

Residual magnetism method: I=20D ~ 40D

I was in the current value of A

D - specimen diameter or maximum width (mm)

The above values are the reference values, and the actual work values shall be determined by the sensitivity test.

14. Magnetic suspension configuration:

Preparation of magnetic suspension of water agent:

Fluorescent magnetic powder: 2-3 g / liter

Dispersant: 0.2%, check the weight of the liquid

Rust inhibitor: 0.5%, check the weight of liquid

Defoaming agent: 0.5 - 1 grams / liter

Preparation of magnetic suspension for oil

(use odorless kerosene = 96 DEG C, flash point)

Fluorescent magnetic powder: 2-3 g / L, odorless kerosene

Dispersant: 0.2%, check the weight of the liquid

Established in year 2000,HUATEC Group is a reliable manufacturer and supplier of testing instruments in Beijing China. HUATEC Group combines all the R/D and production advantage of all its own subsidiaries, takes advantage of its years marketing and sales experience in global market, contributes to offering most qualified competitive products and service to international markets.

HUATEC Group products are composed of all kinds of metal and non-metal testing equipments, such as portable hardness tester, micro hardness tester, shore durometer, vickers hardness tester, Rockwell hardness tester, Brinell hardness tester, portable X-ray flaw detector, mobile X-ray flaw detector, Real-time X-ray image flaw system, holiday detector, digital portable eddy current electrical conductivity meter, digital ultrasonic flaw detector, coating/painting thickness gauge, ultrasonic thickness gauge, vibration tester, surface roughness tester, profile projector, etc, and all of their accessories such as ultrasonic transducer, test block, IQI, lead screen, densimeter, film viewer etc.

HUATEC Group employees include a highly trained staff of engineers for sales and service, that are committed to offer satisfactory products and prompt service to all home and abroad customers.

HUATEC Group, based on most advanced technology in China, is an China famous industry group, focus on development & research and precision production of various testing equipment. The group has two own factories and two sister factories located in area of Beijing, Liaoning, Shandong and Guangzhou. All the products are produced following ISO9001 regulations and the products have been exported to most of world markets in passed years.

Our promise: Reliable quality, competitive price, fast delivery, satisfactory service.