
Cascading 100Base Ethernet Multi Port Fiber Switch With 2 Duplex SC Optical Ports 3 UTP Ports
When using an Ethernet switch or fiber media converter to cascade, we should pay attention to the following problems. In principle, any manufacturer or any type of Ethernet switch or media converter can cascade with each other, but sometimes two switches or fiber media converters cannot be cascaded under some special circumstances. There is a certain limit on the number of cascaded layers between switches or media converters. The most fundamental principle of the successful implementation of cascading is that the distance between any two nodes cannot exceed the maximum span of the media segment. When multiple switches or fiber media converters are cascaded, they should be guaranteed that they all support spanning tree (Spanning-Tree) protocol. It is necessary to prevent loops in the network and allow redundant chain paths to exist.
When cascading, we should try to ensure that the relay link between switches or fiber media converters has enough bandwidth, so full duplex technology and link convergence technology can be used. After the full duplex technology is applied to the switch port, not only the throughput of the corresponding port is doubled, but also the relay distance between the switches increases greatly, making it possible to cascade multiple equipments in different locations and distances. Link aggregation is also called port aggregation, port bundling, and link expansion combination, defined by the IEEE802.3ad standard. That is to say, in order to provide higher bandwidth, better redundancy and load balancing, two devices can be connected in parallel through more than two ports of the same type and transmit data at the same time. Link aggregation technology can not only provide high speed connections between switches or fiber media converter, but also provide high speed channels for the connection between switches, media converters and servers. But it is important to note that not all types of switches or media converters support these two technologies. Please contact Fiberall for more information if you are interested in cascading fiber switch or fiber media converter.
Main Features Of FAFS-FDSES2R3-40 Fiber Media Converter
Two optical interfaces, can implement chain structure network;
Built-in high efficient exchange core to reduce broadcast packets;
Support full duplex and half duplex transmission mode, which can be negotiated automatically;
Support the longest 1536 byte ultra long packet transmission;
Support QoS to ensure VOIP packet transmission;
Support STP spanning tree to form a redundant network;
Low power consumption and low heat, stable work for a long time;
Fiberall provide dual fiber multimode, dual fiber single-mode and single fiber single-mode fiber port for options to meet different needs of users.
Main Characteristics
Port Configuration | Fiber port: 2 | FE port: 3 |
Data rate | Fiber port: 100Mbps | Electrical port: 10/100Mbps |
Optical transceiver | 1×9 | SFP |
Fiber port | FC/ST/SC/LC( for options) | |
Transmitting distance | MM: 2KM | SM: 20-80KM |
Center wavelength | 850nm,1310nm, 1550nm | |
Fiber type | Single mode or multimode | |
Compliant standards | IEEE802.3u, IEEE802.3X,100Base-TX/100Base-FX | |
LAN port working mode | Full duplex / half duplex auto negotiation | |
Power supply | 5V/2A | |
Working temperature | -30℃~+70℃ |
Fiberall Technology (Shenzhen) Co., Ltd
Fiberall Technology (Shenzhen) Co., Ltd was started in 2007 and we are located in Shenzhen China. As a company engaged in fiber optical engineering related products, our main business including: research and development (R&D), manufacturing, marketing; optical engineering solution design; maintenance, consulting service and accessories outsourcing.
Our main products are: All kinds of Fiber PLC Splitters, FBT Couplers, Fiber Cable Assemblies, Patch Cords, Fiber Pigtails, Fiber Adapters, Patch Panels, Fiber Optical Transceivers, OLT (Optical Line Terminal), ONU (Optical Network Unit), FTTx, Equipments & Accessories for Fiber Test, Installation, Maintenance & Repair.
With eight years’ experience in fiber optic, Fiberall established a relatively perfect products and service system, with rich industry experience, comprehensive technology and high-quality team, we are able to provide our customers with OEM & ODM service, project implementation, maintenance, and after-sale service and we have ability to meet different requirement from different customers like distributors, operators, contractors and users etc.
Adhering to the core values of “Honesty, Responsibility, Efficiency, Flexibility, Communication, Mutual Benefit”, and with trust from all old & new customers, support from all partners and effort of our whole team, Fiberall gradually formed a business model of "service to project, based on the market, integrate design, production, marketing and service together", we are committed to providing a full range, high technology, low cost, and ultra expected solution to our customers.